Rancang Bangun Sistem Pengisian Daya Menggunakan PV Untuk Smart Loker
Abstract
This study discusses the design of a Charging System using pv and Smart Lockers, lockers with double security that aims to overcome the safety problems of goods stored in public places. Smart lockers require continuous electricity flow, so Pv is used as an electricity supply for smart lockers. Discusses how to make smart lockers and the energy generated by solar panels. This study aims to find out how to design smart lockers and the energy produced by solar panels. How to make a Smart Locker using RFID and Keypad by determining the components to be used such as Arduino Uno, RFID, 4x4 Keypad, LCD, 2 Channel Relay, Selenoid Door Lock, Buzzer all components are designed and assembled on Aduino pins that have been adjusted by the wiring of each component and programmed using Arduino IDE software. And from the measurement of the energy of the solar panels, And from the measurement of the energy of solar panels it can be concluded that the voltage and current of the solar panels depend on the intensity of the sunlight that is in can be. the voltage reached its peak at 07.00 of 14.47 due to sunny weather and a decrease at 13.00 by 11.14 due to cloudy cloudy weather the highest current was at 09.00. The Monocrystalline 50 Wp solar panel is capable of charging the accu for 6 hours from a voltage of 12.41 volts to 14.55 volts to supply the load from the smart locker.
References
Vaizal Pradana, Holy Lydia Wiharto. 2020. Rancang Bangun Smart Loker Menggunakan RFID Berbasis Arduino Uno. Fakultas Teknik Elektro. Jurnal Universitas 17 Agustus 1945 Surabaya. Vol 1. No. 2.
Tiur Octaviany, Teguh Supriyanto, Syufrijal. 2015. Sistem Keamanan Loker Barang RFID (Radio Frequency Identification) Dengan Pengendali Arduino Uno. Fakultas Teknik. Jurnal Universitas Negeri Jakarta. Vol 2. No. 2.
Ridwan Alief, Darjat, Sudjadi. 2014. Pemanfaatan Teknologi RFID Melalui Kartu Identitas Dosen Pada Prototipe Sistem Ruang Kelas Cerdas. Fakultas Teknik Elektro. Jurnal Universitas Diponegoro Semarang TRANSMISI, 16, (2), 2014, 65.
Erixon Dedy Nawali, Sherwin R.U. A Sompie ST .MT, Novi Tulung ST. MT. 2015. Rancang Bangun Alat Penguras Dan Pengisi Tempat Minum Ternak Ayam Berbasis Mikrokontroler Atmega 16. FakultasTeknik Elektro. Jurnal Universitas Sam Ratulangi Manado. Vol 4. No.7.
Yohanes C Saghoa, Sherwin R. U. A. Sompie, Novi M. Tulung. 2018. Kotak Penyimpan Uang berbasis Mikrokontroler Arduino Uno. Fakultas Teknik Elektro. Jurnal Universitas Sam Ratulangi Manado. Vol. 7. No. 2.
Royen, Abi. “Pengertian, Tujuan Pemakaian dan Jenis Relay”. 26 Februari 2016.
Saptaji, Handayani W. 2015. Mudah belajar Mikrokontroller dengan Arduino. Bandung :Widya Media.
Santoso Heri. 2015. Panduan Praktis Arduino Uno Untuk Pemula. Trenggalek E-Book.
Taufik Dwi Septian Suyadhi. 2010. Buku Pintar Robotika. Andi Offset, Yogyakarta. Fakultas Teknik elektro. Jurnal universitas lampung. Vol 9. No 1
Barwami, Malvino. 2005. Prinsip – Prinsip Elektronika. Jakarta Erlangga 2005.
Yogie El Anwar, Noer Soedjawanto, Ageng Sadnowo Repelianto. 2015. Prototype penggerak pintu pagar Otomatis Berbasis Arduino Uno Atmega 328 dengan sensor sidik jari.
Dr. ir. Saludin Muis, M. Kom. 2013. Prinsip Kerja LCD Dan Pembuatannya (Liquid Crystal Display). Yogyakarta : Graha ilmu.
Dr. ir. Saludin Muis, M. Kom. 2014. Power Supply Jenis Switch mode Perancangan tingkat lanjut. Yogyakarta : Graha Ilmu.
Fungsi Solar Charger Controller Pada Sistem Panel Surya - Janaloka.com. Diakses pada 26 Maret 2021.
Deny Suryana, M Marhaendra Ali. 2016. Pengaruh Temperature/suhu terhadap tegangan yang dihasilkan panel surya jenis monokristalin. Jurnal teknologi proses dan inovasi indrusti. Vol 2, No 1
Hasnawiya Hasan. 2012. Perancangan Pembangkit Listrik tenaga surya di pulau saugi. Fakultas Teknik perkapalan. Jurnal riset dan teknologi kelautan. Vol. 10 No. 2
Surya Darma. 2017. Analisa Perkiraan Kemampuan Daya Yang Dibutuhkan Untuk Perencanaan pembangkit Listrik Tenaga Surya(PLTS). Fakultas Teknik Elektro. Jurnal Ampere. Vol.2 No. 1
